Section 232 U.S. content for Canadian and Mexican industrial equipment: requirements and next steps
How the Section 232 U.S. content rule works for USMCA-qualifying industrial equipment from Canada and Mexico, and what importers need in place to claim it.
- Published
- Oct 28, 2026
- Category
- Insights
- Reading time
- 6 min read
Summary
Since June 8, 2026, certain steel and aluminum derivative articles from Canada and Mexico that qualify for USMCA treatment, mainly mobile industrial equipment such as forklifts, loaders, tractors and mobile cranes and their parts, can enter with their U.S. content at a zero Section 232 duty, up to 40 percent of entered value. The rest of the value pays the 25 percent duty. On October 14, the Commerce Department's Bureau of Industry and Security published the definition of U.S. content that applies to these entries. The reduction can be significant, but it depends on part-level documentation that most importers do not currently hold in one place.
What changed
Proclamation 11032, signed June 1, 2026, modified the Section 232 treatment of USMCA-qualifying goods from Canada and Mexico listed in the proclamation's Annex I-C. The treatment applies to goods entered from June 8, 2026 through December 31, 2027.
CBP's filing instructions (CSMS #68855869) require each article to be reported on two lines. Both lines carry the same HTS classification and the same country of origin, and both use special program indicator "S".
- 9903.82.21, at zero: the U.S. content, up to 40 percent of the article's entered value.
- 9903.82.20, at 25 percent: the non-U.S. content, plus any U.S. content above 40 percent of entered value.
At the 40 percent limit, the duty works out to 15 percent of the article's entered value. CBP's instructions describe this two-line method for derivative steel articles, so importers of aluminum derivative articles should confirm with their broker which headings apply.
A worked example
Take one imported part with an entered value of $100,000. The figures are illustrative and leave out any other duties that apply.
- No U.S. content claimed: the full $100,000 is declared at 25 percent, for $25,000 in duty.
- 30 percent U.S. content documented: $30,000 is reported under 9903.82.21 at zero and $70,000 under 9903.82.20 at 25 percent. The duty is $17,500, a saving of $7,500.
- 60 percent U.S. content documented: only $40,000 can be reported under 9903.82.21. The remaining $60,000, including the $20,000 of U.S. content above the limit, goes under 9903.82.20 at 25 percent. The duty is $15,000, a saving of $10,000.
Above 40 percent, additional U.S. content does not lower the duty further. Whatever is reported under 9903.82.21 still has to be supported by records.
How U.S. content is defined
For entries on or after October 14, 2026, U.S. content means:
- the value attributable to parts that were wholly obtained, entirely produced, or substantially transformed in the United States; and
- to the extent not otherwise accounted for, the value attributable to steel melted and poured, or aluminum or copper smelted and cast, in the United States.
The second element only adds value the first has not already captured. If a part made in the United States is already counted, the U.S.-melted steel inside it cannot be counted again, so the same value is never counted twice.
There is no pre-approval or submission process. Each claim is supported by the importer's own records.
Entries filed June 8 to October 13
Entries filed between June 8 and October 13, 2026 were made under the proclamation's earlier description of U.S. content, which referred only to parts produced in the United States. Importers should review those entries to confirm whether U.S. content was claimed, whether the amount was supported by records, and whether it stayed within the 40 percent limit. Where a claim was overstated or missed, discuss the options with counsel, such as a post summary correction or a prior disclosure.
Operational implications
The information needed to support a claim is held outside the entry. It comes from suppliers, from bills of materials, and from mill certificates showing where the metal was produced. Brokers file the split they are instructed to file, and absent instructions the full value is typically declared at 25 percent.
For companies importing the same parts through more than one broker or port, the U.S. content figure needs to be applied consistently across all of them. Differences between filers result in either unclaimed savings or inconsistencies that may need to be explained later. Because supplier sourcing changes over time, the figures also need periodic review.
The proclamation directs CBP to impose penalties where an importer commits fraud or deliberately misleads the government about U.S. content, and the standard penalty framework for negligent errors continues to apply. Documentation is the primary support for any claim.
In practice, claiming U.S. content means proving it part by part, on every entry, whichever broker files it. Align's part-level classification records each part's origin and content attributes once and keeps them consistent and enforced across every broker, with a record that holds up in an audit.
Recommended next steps
- Identify imported parts that are listed in Annex I-C, are of Canadian or Mexican origin, and qualify for USMCA treatment.
- For each part, map the bill of materials to both elements of the definition and collect supporting supplier declarations and mill certificates.
- Establish the U.S. content figure at the part level, report no more than 40 percent of entered value under 9903.82.21, and issue consistent two-line filing instructions to every broker.
- Review entries filed since June 8. Where U.S. content was overstated or not claimed, consult counsel on a post summary correction or prior disclosure.
- Schedule periodic supplier reviews so declared figures reflect current sourcing.
Looking ahead
A growing share of tariff relief depends on attributes of the part itself, such as origin, content and materials, rather than on the individual shipment. The practical step now is to build part-level U.S. content records and keep them current, ahead of any CBP verification and before the treatment ends on December 31, 2027.
This article is general information and not legal advice. CBP may update its filing guidance as the rule is implemented.
Keep reading
→ Get started
See your trade operation as it actually is.
Connect your customs and product data. See the exposure, the recovery, and the work worth doing first.